Mitsubishi Electric MR-J3-10A-S030 MELSERVO-J3 Servo Drive

New 
On request
Refurbished   
On request
Want to exchange a faulty product?
Receive a discount on your purchase when you turn in a faulty product. Upon receipt, we will check the product to determine its eligibility according to the terms and conditions.
Repair  
Available
We can repair this product for you.
 

Product Information

Product Family: MELSERVO-J3

The Mitsubishi Electric MR-J3-10A-S030 is a MELSERVO-J3 100 W AC servo amplifier for compact machine motion-control systems. This servo drive operates from a 200–230 V AC main circuit supply and supports general-purpose pulse train positioning commands together with analog voltage control for speed or torque applications. Its -S030 designation identifies a special specification version for existing Mitsubishi equipment.

A replacement requires a compatibility check against the original MR-J3-10A-S030 installation, including the motor, controller, cables, parameters and the special -S030 modification. The drive connects to MR Configurator software through its USB / RS-422 configuration interface for parameter setting, servo tuning, monitoring, diagnostic tracing and test operation. Parameters are held in internal non-volatile EEPROM memory, allowing compatible settings to be backed up from the original amplifier and restored to the spare during commissioning.

For troubleshooting, the built-in 7-segment LED display provides local alarm-code information, while MR Configurator adds software monitoring, diagnostic tracing and test-operation functions. Check the selected command method, controller connection, parameter configuration and compatibility of the motor and cables before putting a replacement into service. As a discontinued servo amplifier with a special suffix, the MR-J3-10A-S030 is intended for exact legacy replacement work rather than automatic substitution by a standard MR-J3-10A.

Technical Specifications

ManufacturerMitsubishi Electric
Part numberMR-J3-10A-S030
Model/typeMELSERVO-J3 100 W AC servo amplifier
Product familyMELSERVO-J3
Component typeServo drive
Rated motor power100 W
Main circuit supply voltage200–230 V AC
Control interfaceGeneral-purpose pulse train and analog voltage control
Control and status interfaceDigital and analog I/O with pulse train command input and analog speed/torque command inputs
Configuration interfaceUSB / RS-422
Parameter storageInternal non-volatile EEPROM memory
Parameter backup and restoreSupported through setup software
Diagnostic displayBuilt-in 7-segment LED display
Product lifecycle statusDiscontinued

Programming and Configuration

MR Configurator software supports parameter setting, servo tuning, monitoring, diagnostic tracing and test operation for the MR-J3-10A-S030. The software connects through the drive's USB / RS-422 configuration interface.

The amplifier stores parameters in internal non-volatile EEPROM memory. During replacement work, compatible parameters can be backed up from the original drive and restored to the spare before commissioning.

Communication and System Integration

The MELSERVO-J3 servo drive accepts general-purpose pulse train commands for positioning and analog voltage commands for speed or torque control. Its control and status interface includes digital and analog I/O.

The configuration connection uses USB / RS-422 for MR Configurator software access, including parameterization, monitoring, tuning, diagnostic tracing and test operation. The replacement controller and command method must match the existing installation.

Diagnostics and Status Indication

A built-in 7-segment LED display provides local alarm-code information on the servo amplifier. MR Configurator software adds monitoring, diagnostic tracing and test-operation functions for maintenance and commissioning.

When troubleshooting an existing installation, check the controller connection, selected pulse train or analog command method, parameter configuration, motor compatibility and cable compatibility before commissioning a replacement amplifier.

Replacement and Spare Part Considerations

The MR-J3-10A-S030 is a discontinued Mitsubishi Electric servo amplifier with a special -S030 specification. The exact part number should be matched when replacing an original unit, because a standard MR-J3-10A may not be a direct substitute.

Before installation, compare the replacement with the original equipment configuration, including the compatible motor, cables, controller, command method and stored parameters. Use MR Configurator to back up and restore parameters when the configuration is compatible.

Commissioning includes configuring the replacement drive and confirming the pulse train or analog control connection. The built-in 7-segment display and MR Configurator diagnostic functions support checks after the spare has been installed.

Frequently Asked Questions

What is the Mitsubishi MR-J3-10A-S030?

It is a Mitsubishi Electric MELSERVO-J3 100 W AC servo amplifier for compact motion-control systems, with pulse train and analog voltage command support.

What supply voltage does the MR-J3-10A-S030 use?

The main circuit supply voltage is 200–230 V AC.

Which software is used to configure the MR-J3-10A-S030?

Mitsubishi Electric MR Configurator software is used for parameter setting, servo tuning, monitoring, diagnostic tracing and test operation through the USB / RS-422 interface.

Can parameters be transferred to a replacement drive?

Yes. Parameters are stored in internal non-volatile EEPROM memory, and compatible settings can be backed up from the original amplifier and restored to a replacement through setup software.

What should be checked before replacing this servo amplifier?

Match the exact MR-J3-10A-S030 part number and check the motor, cables, controller, command method, parameters and special -S030 configuration before commissioning.

How can the MR-J3-10A-S030 be diagnosed?

The built-in 7-segment LED display provides local alarm-code information. MR Configurator provides monitoring, diagnostic tracing and test-operation functions.

Take advantage of our exchange formula

A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.

Play it safe with our warranty conditions

Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.​​​​​​​

Data backup and recovery

Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.

Specific firmware and hardware versions

If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.


Disclaimer:
We are not an authorised distributor of Mitsubishi.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.