Siemens 1FT6062-1AF71-4EH1 1FT6 SIMOTICS S Servo Motor

Het item werd toegevoegd aan uw offerteaanvraag
Product Information
The Siemens 1FT6062-1AF71-4EH1 is a 1FT6 SIMOTICS S permanent-magnet synchronous servo motor for precise and dynamic machine-axis motion. It provides 6.0 Nm rated torque at 3000 rpm and supports speeds up to 9100 rpm. The motor uses natural cooling, has an IP65 protection rating, and combines IM B5 mounting with a shaft fitted with a key. An integrated 15 Nm holding brake supports secure axis positioning while stopped.
Replacement integration depends on matching the complete 1FT6062-1AF71-4EH1 part number, the motor winding requirements, brake option, connector arrangement and EnDat encoder compatibility. The motor has circular connectors for the motor winding, holding-brake supply and encoder feedback. Its absolute EnDat 2048 S/R encoder, also identified as encoder A-2048, connects to compatible Siemens SIMODRIVE or SINAMICS drive systems. Commissioning and parameterization can be performed through Siemens STARTER or SIMOCOM U on the connected drive controller, with absolute encoder calibration or homing carried out during replacement motor commissioning when required by the system configuration.
During troubleshooting, use the connected Siemens drive controller or commissioning software to read drive diagnostic messages and monitor encoder signals, winding temperature and drive output currents. Check the motor power and brake connections, encoder connection, drive compatibility and commissioning parameters before returning the axis to service. The 1FT6 1FT6062-1AF71-4EH1 is identified as a Siemens spare part and phase-out product, so a tested replacement or repair route can be relevant when an installed motor fails.
Technical Specifications
| Manufacturer | Siemens |
| Part number | 1FT6062-1AF71-4EH1 |
| Model/type | 1FT6 SIMOTICS S synchronous servo motor |
| Product family | SIMOTICS S |
| Series | 1FT6 |
| Component type | Synchronous servo motor |
| Rated torque | 6.0 Nm |
| Rated speed | 3000 rpm |
| Maximum speed | 9100 rpm |
| Rated current | 4.1 A |
| Holding brake torque | 15 Nm |
| Holding brake power | 17 W |
| Protection rating | IP65 |
| Cooling method | Natural cooling |
| Mounting position | IM B5; IM V1 and IM V3 |
| Shaft design | Shaft with fitted key |
| Encoder type | Absolute encoder EnDat 2048 S/R |
| Encoder interface | EnDat via circular connector |
| Power interface | Circular connector for motor winding and holding brake supply |
| Lifecycle status | Phase-out; identified as a spare part in the Siemens catalog |
Programming and Configuration
Commissioning and parameterization use Siemens STARTER or SIMOCOM U software through the connected Siemens drive controller. The applicable drive configuration must support the 1FT6 motor and its EnDat 2048 S/R absolute encoder.
When a motor is replaced, the drive parameters and motor data must be checked before operation. Absolute encoder calibration or homing may be required during commissioning, depending on the system configuration and the connected drive controller.
Communication and System Integration
The motor provides position and speed feedback through an absolute EnDat 2048 S/R encoder, also identified as encoder A-2048. The encoder interface uses a circular connector.
A separate circular connector provides the motor winding connection and holding-brake supply. The 1FT6 series supports integration with compatible Siemens SIMODRIVE and SINAMICS drive systems, subject to matching the complete motor specification and encoder compatibility.
Diagnostics and Status Indication
Diagnostic messages are displayed by the connected Siemens drive controller or commissioning software rather than by product-specific status LEDs. Commissioning tools can be used for parameterization and for checking the motor and feedback system.
For first-line troubleshooting, monitor the encoder signals, winding temperature and drive output currents. Also check the motor power connection, holding-brake supply, encoder connector, drive compatibility and absolute encoder calibration or homing after motor replacement.
Replacement and Spare Part Considerations
Before ordering a replacement, match the complete Siemens part number 1FT6062-1AF71-4EH1. Confirm the motor winding requirements, 15 Nm brake option, circular connector arrangement, IM B5 mounting, fitted-key shaft and EnDat 2048 S/R encoder.
A replacement motor may require drive parameterization, encoder calibration or homing before the axis can return to service. Verify compatibility with the installed Siemens SIMODRIVE or SINAMICS drive system and use Siemens STARTER or SIMOCOM U where applicable.
This 1FT6 motor is identified as a Siemens spare part and phase-out product. A tested exchange motor or repair assessment can therefore be relevant when the installed unit has failed.
Frequently Asked Questions
Which drive systems are compatible with the Siemens 1FT6062-1AF71-4EH1?
The 1FT6 series is designed for compatible Siemens SIMODRIVE and SINAMICS drive systems. The complete motor specification and EnDat encoder compatibility must match the installed system.
What encoder is fitted to this Siemens servo motor?
The motor has an absolute EnDat 2048 S/R encoder, also identified as encoder A-2048, connected through a circular encoder connector.
Does a replacement motor require commissioning?
Yes. Replacement commissioning can include drive parameterization, absolute encoder calibration or homing, depending on the system configuration and connected Siemens drive controller.
What are the main performance values of the 1FT6062-1AF71-4EH1?
The motor has 6.0 Nm rated torque at 3000 rpm, a maximum speed of 9100 rpm and a rated current of 4.1 A.
How can this motor be diagnosed in a machine?
Use the connected Siemens drive controller or commissioning software to read diagnostic messages and monitor encoder signals, winding temperature and drive output currents. Check the power, brake and encoder connections as part of the first-line checks.
Take advantage of our exchange formula
A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.
Play it safe with our warranty conditions
Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.
Data backup and recovery
Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.
Specific firmware and hardware versions
If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.
Disclaimer:
We are not an authorised distributor of Siemens.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.



