ABB SensyCal FCU400-G Gas Flow Computer and Translator

Het item werd toegevoegd aan uw offerteaanvraag
Product Information
The ABB SensyCal FCU400-G is a gas flow computer and translator for calculating gas flow data and supporting measurement, accounting and billing workflows. It is used with gas metering systems that require measured process signals to be converted, recorded and made available for commercial or operational analysis. The unit accepts pulse, frequency and mA signals from flowmeter technologies including orifice, ultrasonic, swirl and vortex meters. The FCU400-G is part of the ABB SensyCal family and is identified by the model type SensyCal FCU400-G Gas Flow Computer and Translator.
Replacement commissioning requires attention to the installed I/O configuration, terminal arrangement and gas calculation parameters. Depending on the installed hardware, the FCU400 or SensyCal family supports electrically isolated current inputs and outputs, with configurations of up to 8 active current outputs, up to 8 current inputs with transmitter supply or up to 12 voltage/current inputs without transmitter supply. Local parameterization and data transfer are available through the infrared interface, while SensyCal Configuration Software supports parameterization, configuration, data readout and configuration transfer. Optional M-Bus or Modbus communication over RS-485 must match the communication arrangement of the existing installation.
The front-panel graphic display provides process signal monitoring and error indications, and the infrared interface provides local diagnostics. Data logging with billing-date recording and internal non-volatile memory for parameter and billing history data are relevant when maintaining an existing gas measurement system. The FCU400-G is a discontinued legacy product, so a replacement or spare should be checked against the exact model, installed I/O card assembly, terminal configuration, communication option and gas-specific calculation settings before commissioning. ABC Industrial Parts can support repair, exchange and configuration transfer for compatible legacy units.
Technical Specifications
| Manufacturer | ABB |
| Part number | FCU400-G |
| Model/type | SensyCal FCU400-G Gas Flow Computer and Translator |
| Component type | Gas flow computer |
| Product family | SensyCal |
| Primary application | Gas flow calculation, measurement, accounting, and billing |
| Supported flowmeter signals | Pulse, frequency, and mA signals |
| Compatible flowmeter types | Orifice, ultrasonic, swirl, and vortex flowmeters |
| Data logging | Data logger with billing date recording |
| Maximum active current outputs | 8 electrically isolated outputs |
| Maximum current inputs with transmitter supply | 8 electrically isolated inputs |
| Maximum voltage/current inputs without transmitter supply | 12 electrically isolated inputs |
| Local service interface | Infrared interface for local parameterization and diagnostics |
| Communication interfaces | M-Bus and RS-485 |
| Communication protocols | M-Bus and optional Modbus |
| Configuration software | SensyCal Configuration Software for parameterization, configuration, and data readout |
| Configuration storage | Internal non-volatile memory with parameter and billing-date history storage |
| Parameter backup and restore | Supported through configuration transfer |
| Product lifecycle | Discontinued legacy product |
Programming and Configuration
SensyCal Configuration Software is used for parameterization, configuration and data readout. Configuration transfer supports the preparation of a replacement unit, allowing parameters to be transferred rather than recreated manually when the required configuration data is available.
Commissioning a spare involves checking the gas calculation parameters, installed I/O card assembly, terminal configuration and communication arrangement. The FCU400-G stores parameter and billing-date history in internal non-volatile memory, so configuration and historical data requirements should be considered before exchanging the unit.
Communication and System Integration
The FCU400-G accepts pulse, frequency and mA signals from gas flowmeter systems. Compatible flowmeter technologies include orifice, ultrasonic, swirl and vortex meters. Depending on the installed hardware, the FCU400 or SensyCal family supports up to 8 electrically isolated active current outputs, up to 8 electrically isolated current inputs with transmitter supply or up to 12 electrically isolated voltage/current inputs without transmitter supply.
An infrared interface provides local parameterization, diagnostics and configuration access. Optional M-Bus and Modbus communication are available for meter data exchange, with Modbus using RS-485. When replacing a unit, the installed communication option and the connection arrangement must match the existing gas metering system.
Diagnostics and Status Indication
Process signal monitoring and error indications are shown on the front-panel graphic display. Local diagnostics and parameter access are available through the built-in infrared interface, while SensyCal Configuration Software supports configuration and data readout. For a replacement unit, check the process signal connections, I/O card assembly, terminal configuration, communication option and gas calculation parameters during commissioning.
Replacement and Spare Part Considerations
The ABB SensyCal FCU400-G is a discontinued legacy gas flow computer. A compatible spare should be matched by the FCU400-G model type and checked against the installed I/O card assembly, terminal configuration and communication option. The connected flowmeter signal type and the gas calculation parameters must also correspond to the existing installation.
SensyCal Configuration Software supports configuration transfer for replacement preparation. Before commissioning, review the parameter set, billing-date recording requirements, internal billing history and the required M-Bus or Modbus connection. A replacement may require parameter transfer and commissioning work rather than a simple plug-in exchange.
Repair or exchange can be relevant when the existing unit cannot be returned to service through configuration and connection checks. ABC Industrial Parts supports compatible legacy repair and exchange requirements for the FCU400-G.
Frequently Asked Questions
What is the ABB SensyCal FCU400-G used for?
The FCU400-G is a gas flow computer and translator for gas flow calculation, measurement, accounting and billing. It accepts pulse, frequency and mA signals from compatible gas flowmeters.
Which flowmeters can be connected to the FCU400-G?
The FCU400-G supports signals from orifice, ultrasonic, swirl and vortex flowmeters, including pulse, frequency and mA signal types.
Which software is used to configure an FCU400-G replacement?
SensyCal Configuration Software is used for parameterization, configuration, data readout and configuration transfer through the infrared or communication interface.
Does the FCU400-G support M-Bus and Modbus?
The SensyCal FCU400 family supports M-Bus and optional Modbus communication over RS-485. The installed communication option must be checked when matching a replacement.
How does the FCU400-G indicate process and error conditions?
Process signal monitoring and error indications are shown on the front-panel graphic display. Local diagnostics are available through the built-in infrared interface.
What should be checked before commissioning a replacement FCU400-G?
Check the exact FCU400-G model, installed I/O card assembly, terminal configuration, communication option, connected flowmeter signal type and gas-specific calculation parameters. Transfer the required configuration with SensyCal Configuration Software before commissioning.
Take advantage of our exchange formula
A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.
Play it safe with our warranty conditions
Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.
Data backup and recovery
Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.
Specific firmware and hardware versions
If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.
Disclaimer:
We are not an authorised distributor of ABB.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.



